Study on the Migration Mechanism of Temporary Plugging Agent in Artificial Fractures of Deep Geothermal Reservoirs Based on the Euler-Euler Multiphase Flow Model
DOI:
https://doi.org/10.15377/2409-5826.2024.11.2Keywords:
Euler-Euler, Numerical simulation, Deep geothermal resources, Transport of temporary plugging agent, Temporary plugging diverting fracturingAbstract
The successful use of temporary plugging diverting fracturing technology requires an understanding of the migration and plugging processes of temporary plugging agents into artificial fractures under high temperature settings. In this study, a multiphase flow model for the migration of temporary plugging agents in artificial fractures was developed using the Euler-Euler framework, and numerical simulations were conducted at elevated temperatures. Various factors, including plugging agent injection velocity, concentration, carrying fluid viscosity, wall temperature, and fracture width, were systematically analyzed to assess their impact on the agent’s migration behavior. Detailed analyses, using cloud diagrams of particle volume fraction, velocity, and turbulence intensity, clarified the underlying mechanisms influencing the migration process. The results indicate that as the injection velocity increases, the height of blockages near the wellbore decreases, while the blockage length initially increases before declining. Increasing the concentration of the plugging agent leads to a rise in blockage height and a shift in the front edge toward the injection point. Enhancing the viscosity of the carrying fluid enables the plugging agent to migrate deeper into the fracture, improving deep plugging effectiveness. While changes in wall temperature have limited impact on blockage morphology, temperatures exceeding the critical threshold of 573K significantly intensify particle migration. Moreover, increasing fracture width enhances both the height and length of blockages, with the optimal plugging effect observed when the plugging agent diameter is approximately one-third of the fracture width.
Downloads
References
Mortensen JJ. Hot dry rock: a new geothermal energy source. Energy. 1978; 3(5): 639-44. https://doi.org/10.1016/0360-5442(78)90079-8 DOI: https://doi.org/10.1016/0360-5442(78)90079-8
Wan Y, Yuan Y, Zhou C, Liu L. Multiphysics coupling in exploitation and utilization of geo-energy: State-of-the-art and future perspectives. Adv Geo-Energy Res. 2023; 10(1): 7-13. https://doi.org/10.46690/ager.2023.10.02 DOI: https://doi.org/10.46690/ager.2023.10.02
Lu C, Lin W, Gan H, Liu F, Wang G. Occurrence types and genesis models of hot dry rock resources in China. Environ Earth Sci. 2017; 76(19): 646. https://doi.org/10.1007/s12665-017-6947-4 DOI: https://doi.org/10.1007/s12665-017-6947-4
Guiling W, Wenjing LIN, Wei Z, Lu C, Ma F, Gan H. Research on formation mechanisms of hot dry rock resources in China. Acta Geologica Sinica‐English Edition. 2016; 90(4): 1418-13. https://doi.org/10.1111/1755-6724.12776 DOI: https://doi.org/10.1111/1755-6724.12776
Feng Z, Zhao Y, Zhou A, Zhang N. Development program of hot dry rock geothermal resource in the Yangbajing Basin of China. Renew Energy. 2012; 39(1): 490-5. https://doi.org/10.1016/j.renene.2011.09.005 DOI: https://doi.org/10.1016/j.renene.2011.09.005
Wan Z, Zhao Y, Kang J. Forecast and evaluation of hot dry rock geothermal resource in China. Renew Energy. 2005; 30(12): 1831-46. https://doi.org/10.1016/j.renene.2005.01.016 DOI: https://doi.org/10.1016/j.renene.2005.01.016
Brown D W, Duchane D V, Heiken G, Hriscu VT. The enormous potential for Hot Dry Rock geothermal energy. In: Mining the Earth's Heat: Hot Dry Rock Geothermal Energy. Berlin, Heidelberg: Springer; 2012, pp. 17-40. https://doi.org/10.1007/978-3-540-68910-2_2 DOI: https://doi.org/10.1007/978-3-540-68910-2_2
Haraden J. The status of hot dry rock as an energy source. Energy. 1992; 17(8): 777-86. https://doi.org/10.1016/0360-5442(92)90121-F DOI: https://doi.org/10.1016/0360-5442(92)90121-F
Wang G, Zhang W, Ma F, Lin W, Liang J, Zhu X. Overview on hydrothermal and hot dry rock researches in China. China Geol. 2018; 1(2): 273-85. https://doi.org/10.31035/cg2018021 DOI: https://doi.org/10.31035/cg2018021
Razavi O, Lee H P, van Oort E, Olson JE. A coupled geomechanical model for solid plugging of fractures. 52nd U.S. Rock Mechanics/Geomechanics Symposium, 17-20 June, Seattle, WA: ARMA-2018-1237
Lin W, Wang G, Gan H, Wang A, Yue G, Long X. Heat generation and accumulation for Hot Dry Rock resources in the igneous rock distribution areas of southeastern China. Lithosphere. 2021; (Special 5): 2039112. https://doi.org/10.2113/2022/2039112 DOI: https://doi.org/10.2113/2022/2039112
Hofmann H, Babadagli T, Yoon JS, Blöcher G, Zimmermann G. A hybrid discrete/finite element modeling study of complex hydraulic fracture development for enhanced geothermal systems (EGS) in granitic basements. Geothermics. 2016; 64: 362-81. https://doi.org/10.1016/j.geothermics.2016.06.016 DOI: https://doi.org/10.1016/j.geothermics.2016.06.016
AbuAisha M, Loret B, Eaton D. Enhanced Geothermal Systems (EGS): Hydraulic fracturing in a thermo-poroelastic framework. J Pet Sci Eng. 2016; 146: 1179-91. https://doi.org/10.1016/j.petrol.2016.07.027 DOI: https://doi.org/10.1016/j.petrol.2016.07.027
Zhou Z, Jin Y, Zeng Y, Zhang X, Zhou J, Zhuang L, Xin S. Investigation on fracture creation in hot dry rock geothermal formations of China during hydraulic fracturing. Renew Energy. 2020; 153: 301-13. https://doi.org/10.1016/j.renene.2020.01.128 DOI: https://doi.org/10.1016/j.renene.2020.01.128
Tenzer H. Development of hot dry rock technology. Geo-Heat Center Quart Bull. 2001; 22(4): 14-22.
Kuriyagawa M, Tenma N. Development of hot dry rock technology at the Hijiori test site. Geothermics. 1999; 28(4-5): 627-36. https://doi.org/10.1016/S0375-6505(99)00033-4 DOI: https://doi.org/10.1016/S0375-6505(99)00033-4
Li D, Li N, Jia J, Yu H, Fan Q, Wang L, et al. Development status and research recommendations for thermal extraction technology in deep hot dry rock reservoirs. Deep Undergr Sci Eng. 2024. https://doi.org/10.1002/dug2.12080 DOI: https://doi.org/10.1002/dug2.12080
Duchane D. International programs in hot dry rock technology development. Geotherm Resour Counc Bull. 1991; 20(5): 135-42.
Wu X, Li Y. Comparative study on heat extraction performance of three enhanced geothermal systems. Rock Mech Bull. 2023: 2(2): 100041. https://doi.org/10.1016/j.rockmb.2023.100041 DOI: https://doi.org/10.1016/j.rockmb.2023.100041
Yang R, Wang Y, Song G, Shi Y. Fracturing and thermal extraction optimization methods in enhanced geothermal systems. Adv Geo-Energy Res. 2023; 9(2): https://doi.org/10.46690/ager.2023.08.07 DOI: https://doi.org/10.46690/ager.2023.08.07
Weng D, Lei Q, Xu Y, LI Y, Li D, Wang W. Network fracturing techniques and its application in the field. Acta Petrolei Sinica. 2011; 32(2): 280.
Zhou Z, Wang D, Zheng B, Liu X, Yang K. Comparative experimental investigation on permeability and pressure bearing capacity of different types of temporary plugging bodies. Unconv Resour. 2024, 4: 100062. https://doi.org/10.1016/j.uncres.2023.08.004 DOI: https://doi.org/10.1016/j.uncres.2023.08.004
Li M, Guo J, Zhou F, Li M, Chen J, Liu H, et al. Experimental study on plugging behavior of degradable diverters in partially open fracture in temporary plugging and diverting fracturing. ACS Omega. 2023; 8(15): 14066-76. https://doi.org/10.1021/acsomega.3c00689 DOI: https://doi.org/10.1021/acsomega.3c00689
Zhang L, Zhou F, Feng W, Pournik M, Li Z, Li X. Experimental study on plugging behavior of degradable fibers and particulates within acid-etched fracture. J Pet Sci Eng. 2020; 185: 106455. https://doi.org/10.1016/j.petrol.2019.106455 DOI: https://doi.org/10.1016/j.petrol.2019.106455
Guo J, Zhao F, Ren J. Experimental study on plugging behavior of temporary plugging particles during dynamic increase of fracture width. International Petroleum Technology Conference. February 12, 2024. Dhahran, Saudi Arabia: IPTC; 2024. https://doi.org/10.2523/IPTC-23174-MS DOI: https://doi.org/10.2523/IPTC-23174-MS
Feng W, Yang C, Zhou F. Experimental study on surface morphology and relevant plugging behavior within acid-etched and unetched fractures. J Nat Gas Sci Eng. 2021; 88: 103847. https://doi.org/10.1016/j.jngse.2021.103847 DOI: https://doi.org/10.1016/j.jngse.2021.103847
Yuan L, Zhou F, Li B, Gao J, Yang X, Cheng J, et al. Experimental study on the effect of fracture surface morphology on plugging efficiency during temporary plugging and diverting fracturing. J Nat Gas Sci Eng. 2020, 81: 103459. https://doi.org/10.1016/j.jngse.2020.103459 DOI: https://doi.org/10.1016/j.jngse.2020.103459
Guo J, Zhan L, Lu Q, Qi T, Liu Y, Wang X, et al. Plugging behaviors of temporary plugging particles in hydraulic fractures. Pet Explor Dev. 2023; 50(2): 464-72. https://doi.org/10.1016/S1876-3804(23)60401-X DOI: https://doi.org/10.1016/S1876-3804(23)60401-X
Yang C, Feng W, Zhou F. Formation of temporary plugging in acid-etched fracture with degradable diverters. J Pet Sci Eng. 2020; 194: 107535. https://doi.org/10.1016/j.petrol.2020.107535
Zhang L, Zhou F, Feng W, Cheng J. Temporary plugging mechanism of degradable diversion agents within reproduced acid-etched fracture by using 3D printing model. Abu Dhabi International Petroleum Exhibition and Conference, November 11-14, 2019. Abu Dhabi, UAE: SPE; 2019. https://doi.org/10.2118/197132-MS DOI: https://doi.org/10.2118/197132-MS
Yang C, Feng W, Zhou F. Formation of temporary plugging in acid-etched fracture with degradable diverters. J Pet Sci Eng. 2020, 194: 107535. https://doi.org/10.1016/j.petrol.2020.107535 DOI: https://doi.org/10.1016/j.petrol.2020.107535
Cortez-Montalvo J, Vo L, Inyang U, Parton C, Fulton D. Early steps towards laboratory evaluation of diversion in hydraulic fractures. International Petroleum Technology Conference, December 6-9, 2015. Doha, Qatar: IPTC; 2015. https://doi.org/10.2523/IPTC-18262-MS DOI: https://doi.org/10.2523/IPTC-18262-MS
Yang C, Zhou F, Feng W, Tian Z, Yuan L, Gao L. Plugging mechanism of fibers and particulates in hydraulic fracture. J Pet Sci Eng. 2019; 176: 396-402. https://doi.org/10.1016/j.petrol.2019.01.084
Gomaa A M, Nino-Penaloza A, Castillo D, McCartney E, Mayor J. Experimental investigation of particulate diverter used to enhance fracture complexity. SPE International Conference and Exhibition on Formation Damage Control, February 24-26, 2016. Lafayette, Louisiana, USA: SPE; 2016. https://doi.org/10.2118/178983-MS DOI: https://doi.org/10.2118/178983-MS
Yang C, Zhou F, Feng W, Tian Z, Yuan L, Gao L. Plugging mechanism of fibers and particulates in hydraulic fracture. J Pet Sci Eng. 2019; 176: 396-402. https://doi.org/10.1016/j.petrol.2019.01.084 DOI: https://doi.org/10.1016/j.petrol.2019.01.084
Liu X, Zhang X, Wen Q, Zhang S, Liu Q, Zhao J. Experimental research on the proppant transport behavior in nonviscous and viscous fluids. Energy Fuels. 2020; 34(12): 15969-82. https://doi.org/10.1021/acs.energyfuels.0c02753 DOI: https://doi.org/10.1021/acs.energyfuels.0c02753
Liu G. Application of the two-fluid model with kinetic theory of granular flow in liquid–solid fluidized beds. In: Kyzas G, Mitropoulos AC, Eds. Granularity in Materials Science. InTech. 2018, pp. 3-23. https://doi.org/10.5772/intechopen.79696 DOI: https://doi.org/10.5772/intechopen.79696
Enwald H, Peirano E, Almstedt AE. Eulerian two-phase flow theory applied to fluidization. Int J Multiphase Flow. 1996; 22: 21-66. https://doi.org/10.1016/S0301-9322(96)90004-X DOI: https://doi.org/10.1016/S0301-9322(96)90004-X
Zheng Z, Zhuoli X. Numerical simulation of fluid-solid two-phase flows. CIESC J. 2001; 52(1): 1.
Wang W, Li Y. Progress of the simulation of particle-fluid two-phase flow. Prog Chem. 2000; 12(02): 208.
Feng ZG, Ponton MEC, Michaelides EE, Mao S. Using the direct numerical simulation to compute the slip boundary condition of the solid phase in two-fluid model simulations. Powder Technol. 2014; 265: 88-97. https://doi.org/10.1016/j.powtec.2014.01.020 DOI: https://doi.org/10.1016/j.powtec.2014.01.020
Zhang G, Li M, Gutierrez M. Simulation of the transport and placement of multi-sized proppant in hydraulic fractures using a coupled CFD-DEM approach. Adv Powder Technol. 2017; 28(7): 1704-18. https://doi.org/10.1016/j.apt.2017.04.008 DOI: https://doi.org/10.1016/j.apt.2017.04.008
Zheng Y, Wang HZ, Li YJ, Tian GH, Yang B, Zhao CM, et al. Effect of proppant pumping schedule on the proppant placement for supercritical CO2 fracturing. Petrol Sci. 2022; 19(2): 629-38. https://doi.org/10.1016/j.petsci.2021.11.002 DOI: https://doi.org/10.1016/j.petsci.2021.11.002
Kou R, Moridis GJ, Blasingame TA. Analysis and modeling of proppant transport in inclined hydraulic fractures. SPE Hydraulic Fracturing Technology Conference and Exhibition, January 23-25, 2018. The Woodlands, Texas, USA: SPE, 2018. https://doi.org/10.2118/189856-MS DOI: https://doi.org/10.2118/189856-MS
Qin H, Wang D, Deng Y, Han D, Yu B, Sun D. study on transport law of temporary plugging agent in artificial fractures of hot dry rocks. J Eng Thermophys. 2022; 43(09): 2397-403. https://doi.org/10.1016/j.geothermics.2023.102714
Wang D, Qin H, Zheng C, Sun D, Yu Bo. Transport mechanism of temporary plugging agent in complex fractures of hot dry rock: A numerical study. Geothermics. 2023; 111: 102714. https://doi.org/10.1016/j.geothermics.2023.102714 DOI: https://doi.org/10.1016/j.geothermics.2023.102714
Zheng C, Wang D, Yu Bo, Sun D, Han D. Numerical investigation on the migration law of temporary plugging agent in rough fractures based on CFD-DEM coupling. J Eng Thermophys. 2023; 44(02):422-9.
Zheng C, Wang D, Wang Q, Sun S, Sun D, Yu B. The migration mechanism of temporary plugging agents in rough fractures of hot dry rock: A numerical study. Phys Fluids. 2024, 36(2): 023323. https://doi.org/10.1063/5.0185662 DOI: https://doi.org/10.1063/5.0185662
Tong S, Kishore K. Mohanty. Proppant transport study in fractures with intersections. Fuel. 2016; 181: 463-77. https://doi.org/10.1016/j.fuel.2016.04.144 DOI: https://doi.org/10.1016/j.fuel.2016.04.144
Downloads
Published
Issue
Section
License
Copyright (c) 2024 Zirui Yang, Daobing Wang, Zongze Li, Yue Wu, Bo Yu
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
All the published articles are licensed under the terms of the Creative Commons Attribution Non-Commercial License (CC BY-NC 4.0) which permits unrestricted, non-commercial use, distribution and reproduction in any medium, provided the work is properly cited.
